National Item Identification Number
00-465-2719
National Stock Number
Item Name
WASHER,FLAT
Federal Supply Class
5310
Referenced on: http://gasturbinegenerators.tpub.com//TM-5-6115-612-24P/css/TM-5-6115-612-24P_335.htm
Referenced on: http://gasturbinegenerators.tpub.com//TM-5-6115-612-24P/css/TM-5-6115-612-24P_390.htm
Referenced on: http://generators.tpub.com//TM-5-6115-627-14P/css/TM-5-6115-627-14P_116.htm
Referenced on: http://generators.tpub.com//TM-5-6115-627-14P/css/TM-5-6115-627-14P_135.htm
Referenced on: http://generators.tpub.com//TM-5-6115-629-14P/css/TM-5-6115-629-14P_127.htm
Referenced on: http://generators.tpub.com//TM-5-6115-629-14P/css/TM-5-6115-629-14P_135.htm
Referenced on: http://generators.tpub.com//TM-5-6115-629-14P/css/TM-5-6115-629-14P_152.htm
Referenced on: http://generators.tpub.com//TM-9-6115-643-24P/css/TM-9-6115-643-24P_154.htm
Referenced on: http://generators.tpub.com//TM-9-6115-643-24P/css/TM-9-6115-643-24P_179.htm
Referenced on: http://generators.tpub.com//TM-9-6115-643-24P/css/TM-9-6115-643-24P_211.htm
Referenced on: http://generators.tpub.com//TM-9-6115-644-24P/css/TM-9-6115-644-24P_169.htm
Referenced on: http://generators.tpub.com//TM-9-6115-644-24P/css/TM-9-6115-644-24P_194.htm
Referenced on: http://generators.tpub.com//TM-9-6115-644-24P/css/TM-9-6115-644-24P_228.htm
Referenced on: http://generators.tpub.com//TM-9-6115-650-14P/css/TM-9-6115-650-14P_108.htm
Referenced on: http://generators.tpub.com//TM-9-6115-650-14P/css/TM-9-6115-650-14P_127.htmDescription
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use SHIM. For items fabricated from ceramic or electrically rated materials by specification or industry standards use INSULATOR (1), WASHER. Excludes DISK, VALVE, graphite impregnated and lubricated items.
Commercial and Government Entity Code (Supplier Data)
D9182
NSN (National Stock Number) 5310-00-465-2719, 5310004652719 NIIN (National Identification Number) 00-465-2719, 004652719
Part Numbers (Reference Numbers)
AN961-816T
AN961-816T
Required Categories
MATERIAL
MATERIAL DOCUMENT AND CLASSIFICATION
SURFACE TREATMENT
SURFACE TREAT
Required Description
COPPER ALLOY 270 OVERALL
QQ-W-321 1/2 HARD FED SPEC 1ST MATERIAL RESPONSE OR
Q