National Item Identification Number
01-124-6463
National Stock Number
Item Name
WASHER,FLAT
Federal Supply Class
5310
Referenced on: http://www.tpub.com/content/automotiveenginemechanics/TM-9-2815-225-34P/css/TM-9-2815-225-34P_876.htm
Referenced on: http://www.tpub.com/content/automotiveenginemechanics/TM-9-2815-225-34P/css/TM-9-2815-225-34P_894.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-1/css/TM-5-3820-205-24P-1_355.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-1/css/TM-5-3820-205-24P-1_392.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-1/css/TM-5-3820-205-24P-1_429.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-2/TM-5-3820-205-24P-20345.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-2/TM-5-3820-205-24P-20380.htm
Referenced on: http://www.tpub.com/content/constructioncrushers/TM-5-3820-205-24P-2/TM-5-3820-205-24P-20414.htm
Referenced on: http://www.tpub.com/content/fuelpumps/TM-10-4320-307-24P/css/TM-10-4320-307-24P_278.htm
Referenced on: http://www.tpub.com/content/fuelpumps/TM-10-4320-307-24P/css/TM-10-4320-307-24P_319.htm
Referenced on: http://www.tpub.com/content/fuelpumps/TM-10-4320-307-24P/css/TM-10-4320-307-24P_394.htm
Referenced on: http://www.tpub.com/content/trucks5ton/TM-9-2320-272-24P-2/TM-9-2320-272-24P-20855.htm
Referenced on: http://www.tpub.com/content/trucks5ton/TM-9-2320-272-24P-2/TM-9-2320-272-24P-21043.htmDescription
A washer having a centrally located hole with a solid or laminated cross-section and two flat parallel bearing surfaces. The hole must be 75 percent or less than the largest dimension and the bearing surface finish is greater than 32 microinch (0.8 micrometer). The thickness cannot exceed 25 percent of the largest outside dimension. When the largest outside dimension is less than 1/4 inch or 6mm, the thickness must be 0.006 inches (0.15mm) or greater and for items 1/4 inch (6mm) or larger, the thickness must be 0.016 inches (0.4mm) or greater. The maximum tolerance is applied to dimensions and used as a determining factor. Items with separable lamination use SHIM. For items fabricated from ceramic or electrically rated materials by specification or industry standards use INSULATOR (1), WASHER. Excludes DISK, VALVE, graphite impregnated and lubricated items.
Commercial and Government Entity Code (Supplier Data)
Z0009
INTERNATIONAL TRUCKS AUSTRALIA
LIMITED
PRINCES HWY
DANDENONG
3175
AUSTRALIA
K4843
15434
CUMMINS INC
500 JACKSON ST
COLUMBUS
IN
47201
812-377-7437
NSN (National Stock Number) 5310-01-124-6463, 5310011246463 NIIN (National Identification Number) 01-124-6463, 011246463
Part Numbers (Reference Numbers)
CU193136
193136
193136
Required Categories
Required Description
